
At high pressure and temperature, the bolted flange joint between a valve body and its bonnet becomes a design problem. The flange must be thick, the bolting must be large, and the gasket must hold under thermal cycling. A pressure seal valve solves this by using the line pressure itself to tighten the bonnet seal.
This article explains how that works, where pressure seal valves are used, and what engineers and buyers should check before specifying one.
How a pressure seal bonnet works
In a conventional bolted bonnet valve, a gasket is clamped between the bonnet flange and the body flange by studs and nuts. Internal pressure acts on the bonnet and tries to lift it, which works against the gasket load. As pressure rises, the bolts must carry more load, and the flange must grow accordingly.
In a pressure seal valve, the bonnet is fitted inside the body. A sealing ring, commonly of soft iron, graphite or a similar material, sits between the bonnet and the body bore. A retaining or segment ring locks the bonnet in position. When the valve is pressurised, the pressure pushes the bonnet upward against the sealing ring and squeezes it into the gap, so the seal becomes tighter as pressure rises. This is why the design is called self-energising.
Main components
| Component | Function |
|---|---|
| Body | Contains pressure; has an internal recess for the bonnet and seal |
| Bonnet | Fits inside the body and carries the stem and packing |
| Pressure seal gasket | Metal or graphite ring that seals between the bonnet and body |
| Thrust and segment rings | Hold the bonnet against the pressure load |
| Yoke and stem | Support and move the closure element |
| Wedge, disc or plug | Closure element, depending on valve type |
| Seat rings | Provide sealing surface against the closure element |
Why not simply use a thicker bolted bonnet?
For lower pressure classes, a bolted bonnet is simple and economical. As class and temperature increase, however, the bonnet flange and bolting grow quickly, adding weight, cost and thermal inertia. A pressure seal bonnet removes the large bolted flange, so the body is lighter and more compact at high ratings. It also copes well with thermal cycling because the seal tightens with pressure instead of relying on bolt preload that may relax over time.
Types of pressure seal valves
- Pressure seal gate valves, used for isolation of high-pressure steam and feedwater lines
- Pressure seal globe valves, used where tight shut-off and some regulation are required
- Pressure seal check valves, used to prevent reverse flow in high-pressure discharge lines
See our pressure seal valves page for the configurations we supply.
Typical applications
Pressure seal valves are widely used in thermal power stations, where main steam, hot reheat and boiler feedwater lines run at high pressures and temperatures. They also appear in refineries and petrochemical plants on hot hydrocarbon lines, in high-pressure steam headers and in some oil and gas processing duties.
- Main steam and reheat steam isolation
- Boiler feed pump discharge and feedwater lines
- High-pressure steam headers in process plants
- Hot oil and heavy hydrocarbon lines
- Combined cycle and cogeneration plants
For power plant considerations, read how to select industrial valves for power plants.
Pressure classes and materials
Pressure seal valves are generally specified for higher classes, often from Class 600 or 900 upward, although the right class depends on the design pressure and temperature. Our guide to pressure classes explains how to read the ratings.
Body materials follow temperature. Carbon steel (ASTM A216 WCB) suits moderate temperatures, and chrome-moly steels such as ASTM A217 WC6 or WC9 are common for high-temperature steam. Forged alternatives exist in smaller sizes. Trims are often hard-faced for seat life under steam. Always confirm the grade and its availability for each enquiry.
Advantages and limitations
| Advantages | Limitations |
|---|---|
| Seal tightens as pressure increases | Needs adequate initial preload for sealing at low pressure |
| Lighter and more compact at high classes | Higher cost than bolted bonnets at lower classes |
| Good tolerance of thermal cycling | Bonnet removal and gasket renewal need care and manufacturer guidance |
| Fewer large bonnet bolts to maintain | Not normally needed for low-pressure services |
Installation and maintenance points
The bonnet seal must be assembled exactly as the manufacturer specifies, including the preload on the cover and the condition of the sealing ring. Never reuse a deformed sealing ring. During commissioning of steam lines, warm the valve gradually to avoid thermal shock. Where a valve is repaired, record the bonnet disassembly and confirm that the retaining parts are fully seated before returning it to service. Good practice also includes keeping the stem and packing clean, and checking for packing leakage during start-up.
Standards to consider
Pressure–temperature ratings follow ASME B16.34, and inspection and testing commonly follows API 598. Many projects specify design requirements through API 600 or a company specification; editions differ in how they treat pressure seal bonnets, so confirm the document your project cites. Our quality and standards page summarises how we approach documentation.
Pressure seal or bolted bonnet: which should you choose?
There is no single pressure threshold that decides the matter, because it also depends on temperature, size and the owner’s standards. As a rough guide, bolted bonnet valves remain the default for lower pressure classes and moderate temperatures, where they are simpler and cheaper. Pressure seal valves become attractive as the class rises, especially in steam service with frequent heat-up and cool-down cycles, where a bolted joint may relax and begin to leak.
Ask three questions. First, what are the design pressure and temperature, and does the line cycle? Second, what does the plant’s piping specification require for that class? Third, who will maintain the valve, and are they familiar with pressure seal bonnet procedures? A well-chosen bolted bonnet valve that the maintenance team understands may serve better than a pressure seal valve that is disassembled incorrectly.
Common problems and how to avoid them
- Leakage at the bonnet during low-pressure start-up. The seal relies on pressure, so confirm the assembly preload and follow the manufacturer’s start-up procedure.
- Damaged sealing ring after maintenance. Sealing rings are normally replaced, not reused, after the bonnet has been removed.
- Thermal shock on steam lines. Warm the line gradually, and drain condensate before opening the valve.
- Stem packing leakage. Check gland tightness during commissioning and the first thermal cycles.
- Incorrect parts after repair. Keep records and use the retaining and thrust parts specified for that valve.
Most problems come from handling and procedure rather than design, so training and clear documentation matter as much as the valve selection.
Selection checklist
- Define design pressure, temperature and the fluid.
- Select valve type: gate, globe or check.
- Choose body and trim materials for the temperature.
- Confirm pressure class and end connections, usually butt-weld at high class.
- State operator, such as gear or actuator.
- List the standard, testing and documentation requirements.
- Send the data sheet via Request a Quote.
Frequently asked questions
What is the main benefit of a pressure seal valve?
The bonnet seal tightens as line pressure increases, so the design stays compact and reliable at high pressure and temperature.
Are pressure seal valves used for low-pressure lines?
Rarely. At lower classes, bolted bonnet valves are simpler and more economical.
Which valve types are available with pressure seal bonnets?
Gate, globe and check valves are the most common.
Can a pressure seal valve be repaired on site?
Often yes, but bonnet disassembly and sealing ring renewal must follow the manufacturer’s procedure.
References and further reading
Standards and codes are published by their issuing bodies. Always use the current edition named in your project specification.


